Sattler Tech Corp. v. Humancentric Ventures, LLC

Trials@uspto.gov 	Paper 9
571-272-7822 	Entered: July 26, 2019
UNITED STATES PATENT AND TRADEMARK OFFICE
_____________
BEFORE THE PATENT TRIAL AND APPEAL BOARD
_____________
SATTLER TECH CORP.,
Petitioner,
v.
HUMANCENTRIC VENTURES, LLC,
Patent Owner.
_____________
Case PGR2019-00030
Patent D823,093 S
_____________
Before SCOTT A. DANIELS, BART A. GERSTENBLITH, and
CHRISTOPHER G. PAULRAJ, Administrative Patent Judges.
GERSTENBLITH, Administrative Patent Judge.
DECISION
Institution of Post-Grant Review
35 U.S.C. § 324

PGR2019-00030
Patent D823,093 S
2
I. 	INTRODUCTION
A. 	Background
Sattler Tech Corp. (“Petitioner”) filed a Petition (Paper 1, “Pet.”)
requesting institution of a post-grant review of the design claim of
U.S. Patent No. D823,093 S (Ex. 1001, “the ’093 patent”). Humancentric
Ventures, LLC (“Patent Owner”) did not file a preliminary response.
We review the Petition under 35 U.S.C. § 324(a), which provides that
a post-grant review may not be instituted unless “it is more likely than not
that at least 1 of the claims challenged in the petition is unpatentable.”
35 U.S.C. § 324(a). Upon consideration of the present record and for the
reasons explained below, we determine Petitioner has satisfied its burden
under § 324. Thus, we institute a post-grant review.
B. 	Related Proceedings
The parties indicate the sole related matter involving the ’093 patent is
Case No. 2:18-cv-093321-PSG-JPR (N.D. Cal.). Pet. 3; Paper 6, 2.
C. 	Real Parties in Interest
Petitioner identifies itself as the sole real party in interest. Pet. 2.
Patent Owner similarly identifies itself as the sole real party in interest.
Paper 6, 1.
D. 	The ’093 Patent
The ’093 patent is titled “VESA MOUNT ADAPTER BRACKET”
and claims “[t]he ornamental design for a VESA mount adapter bracket, as
shown and described.” Ex. 1001, [54], [57]. The ’093 patent includes six
1 Patent Owner mistakenly identifies the case number as “2:18-cv-09322” in
its Mandatory Notice. Paper 6, 2.

PGR2019-00030
Patent D823,093 S
3
figures, each of which is reproduced below. The ’093 patent explains that
“[t]he broken lines [in the figures] represent portions of the article and form
no part of the claimed design.” Id. at DESCRIPTION.
Figure 1, reproduced above, shows “a perspective view of a VESA mount
adapter bracket.” Id.
Figure 2, reproduced above, shows “a front view.” Id.

PGR2019-00030
Patent D823,093 S
4
Figure 3, reproduced above, shows “a back view.” Id.
Figure 4, reproduced above, shows “a right side view.” Id. The ’093 patent
explains that “the left side view” is “a mirror image of FIG. 4.” Id.

PGR2019-00030
Patent D823,093 S
5
Figure 5, reproduced above, shows “a top view.” Id.
Figure 6, reproduced above, shows “a bottom view.” Id.
As reflected in the figures above, the claimed portions of the design
include: (1) top and bottom tabs and (2) eight raised grommets arranged in
diagonal pairs toward the four corners of the plate.2
E. 	The Asserted Ground of Unpatentability
Petitioner’s sole challenge as set forth in the Petition is that the claim
of the ’093 patent is unpatentable under 35 U.S.C. § 171 for lacking
ornamentality. Pet. 3, 17.
2 The plate is the portion of the adapter bracket shown in broken lines and,
thus, is not part of the claimed design.

PGR2019-00030
Patent D823,093 S
6
II. 	ELIGIBILITY OF PATENT FOR POST-GRANT REVIEW
The post-grant review provisions of section six of the Leahy-Smith
America Invents Act (“AIA”), Pub L. No. 112-29, 125 Stat. 284 (2011),
apply only to patents subject to the first inventor to file provisions of the
AIA. AIA § 6(f)(2)(A). Specifically, the first inventor to file provisions
apply to any application for patent, and to any patent issuing thereon, that
contains or contained at any time a claim to a claimed invention that has an
effective filing date on or after March 16, 2013. AIA § 3(n)(1).
Furthermore, “[a] petition for a post-grant review may only be filed not later
than the date that is 9 months after the date of the grant of the patent or of
the issuance of a reissue patent (as the case may be).” 35 U.S.C. § 321(c);
see also 37 C.F.R. § 42.202(a) (setting forth the same).
The ’093 patent issued on July 17, 2018. Ex. 1001, [45]. The Petition
was filed on January 15, 2019. Paper 3, 1. Therefore, the Petition was filed
within nine months of the ’093 patent issuance.
Additionally, the earliest effective filing date for the ’093 patent is
February 17, 2017. Ex. 1001, [22]. Therefore, the ’093 patent is subject to
the first inventor to file provisions of the AIA.
Petitioner certifies that the ’093 patent “is available for post-grant
review and that Petitioner is not barred or estopped from requesting a
post-grant review of the ’093 Patent.” Pet. 1. At this stage of the
proceeding, Patent Owner has not challenged Petitioner’s contentions as to
the eligibility of the ’093 patent for post-grant review.
On this record, we agree with Petitioner that the ’093 patent is eligible
for post-grant review.

PGR2019-00030
Patent D823,093 S
7
III. 	ANALYSIS
A. 	Legal Standard
Section 171(a) of Title 35 of the United States Code provides:
“Whoever invents any new, original and ornamental design for an article of
manufacture may obtain a patent therefor, subject to the conditions and
requirements of this title.” 35 U.S.C. § 171(a) (2018) (emphasis added).
“[A] design patent can be declared invalid if the claimed design is primarily
functional rather than primarily ornamental, i.e., if the claimed design is
dictated by the utilitarian purpose of the article.” High Point Design LLC v.
Buyers Direct, Inc., 730 F.3d 1301, 1315 (Fed. Cir. 2013) (internal
quotations and citations omitted). “An article of manufacture necessarily
serves a utilitarian purpose, and the design of a useful article is deemed to be
functional when the appearance of the claimed design is dictated by the use
or purpose of the article.” L.A. Gear, Inc. v. Thom McAn Shoe Co., 988 F.3d
1117, 1123 (Fed. Cir. 1993) (citation omitted). “If the particular design is
essential to the use of the article, it can not [sic] be the subject of a design
patent.” Id. “While analyzing elements of the design may be appropriate in
some circumstances, the determination of whether the patented design is
dictated by the function of the article of manufacture must ultimately rest on
an analysis of its overall appearance.” Berry Sterling Corp. v. Pescor
Plastics, Inc., 122 F.3d 1452, 1456 (Fed. Cir. 1997).
The U.S. Court of Appeals for the Federal Circuit has explained that
although there is no “particular test for determining whether a claimed
design is dictated by its function[,] [the court] has often focused . . . on the
availability of alternative designs as an important—if not dispositive—factor
in evaluating the legal functionality of a claimed design.” Ethicon Endo-

PGR2019-00030
Patent D823,093 S
8
Surgery, Inc. v. Covidien, Inc., 796 F.3d 1312, 1329–30 (Fed. Cir. 2015); see
PHG Techs., LLC v. St. John Cos., 469 F.3d 1361, 1367 (Fed. Cir. 2006)
(“When there are several ways to achieve the function of an article of
manufacture, the design of the article is more likely to serve a primarily
ornamental purpose.” (quoting Rosco, Inc. v. Mirror Lite Co., 304 F.3d
1373, 1378 (Fed. Cir. 2002))). “[A] full inquiry with respect to alleged
alternative designs includes a determination as to whether the alleged
‘alternative designs would adversely affect the utility of the specified
article,’ such that they are not truly ‘alternatives’ within the meaning of [the
Federal Circuit’s] case law.” PHG, 469 F.3d at 1367 (quoting Rosco, 304
F.3d at 1378).
In Berry Sterling, the Federal Circuit provided additional factors to
consider in a situation “where the existence of alternative designs is not
dispositive of the invalidity inquiry.” Ethicon, 796 F.3d at 1330. Those
factors include:
[1] whether the protected design represents the best design;
[2] whether alternative designs would adversely affect the utility
of the specified article;
[3] whether there are any concomitant utility patents;
[4] whether the advertising touts particular features of the design
as having specific utility; and
[5] whether there are any elements in the design or an overall
appearance clearly not dictated by function.
Berry Sterling, 122 F.3d at 1456, quoted in PHG, 469 F.3d at 1366–67. The
Federal Circuit, however, explained that although evaluating these other
factors “‘might’ be relevant to assessing whether the overall appearance of a
claimed design is dictated by functional considerations. . . .[,] an inquiry into
whether a claimed design is primarily functional should begin with an

PGR2019-00030
Patent D823,093 S
9
inquiry into the existence of alternative designs.” Ethicon, 796 F.3d at 1330
(citations omitted).
B. 	Discussion
Petitioner explains that VESA mount adapter brackets are used in
connection with “the Video Electronics Standards Association (VESA) Flat
Display Mounting Interface Standard, Copyright 2006” (“the VESA FDMI
Standard”). Pet. 9 (citing Ex. 1002). As Petitioner explains, the purpose of
the VESA FDMI Standard is “to provide industry standard mounting
interfaces for Flat Displays (FDs) such as flat panel monitors, flat displays
and flat TVs.” Ex. 1002, 1; see Pet. 9. Petitioner contends the claimed
VESA mount adapter bracket “is designed specifically to fit onto the back of
certain video monitors so they can attach to VESA [monitor] mount systems
[i.e., using the VESA FDMI standard,] instead of a stand that came with the
monitors.” Pet. 9.
1. 	Functionality of the Claimed Design
Petitioner argues that the appearance of several, if not all, components
of the claimed adapter bracket are dictated by their use and purpose, and,
therefore, the claimed design is, as a whole, functional. Id. at 10–17. In
particular, Petitioner discusses the tabs and the grommets.
a. 	Tabs
Petitioner contends that the top tab of the VESA mount adapter
bracket “fits atop a lower bulge on the back of a video monitor to secure the
top tab via screw to the video monitor.” Id. at 10. Petitioner provides the
following pictures to illustrate this arrangement from the Amazon.com
webpage (https://www.amazon.com/dp/B01DNCP7HW) where an alleged

PGR2019-00030
Patent D823,093 S
10
commercial embodiment of the VESA mount adapter bracket design of the
’093 patent is offered for sale. Id. (citing Ex. 1004, 1; Ex. 1005, 1).
The two pictures reproduced above show the top tab of the VESA mount
adapter bracket connected to the back of a video monitor via a screw. See
Ex. 1004, 1; Ex. 1005, 1.
Petitioner contends the bottom tabs of the VESA mount adapter
bracket of the ’093 patent “fit into preexisting slots on the back of a video
monitor,” as shown in the picture below from the same Amazon.com
webpage. Pet. 12 (citing Ex. 1003, 6).
The picture reproduced above shows the bottom tabs of the VESA mount
adapter bracket inserted into slots in the back of a video monitor. See
Ex. 1003, 6.

PGR2019-00030
Patent D823,093 S
11
Petitioner asserts “the tabs must be positioned and sized as they are –
else they won’t fit the monitor.” Pet. 12. Petitioner contends “[t]he top tab
is shaped as minimally as possible to provide support for the bracket of the
’093 Patent.” Id.
b. 	Grommets
Petitioner contends that at least three features of the grommets are
dictated primarily by function: (a) spacing, (b) size, and (c) raised edges.
Id. at 13–17. Petitioner asserts that the VESA FDMI Standard dictates the
claimed spacing and size of the grommets as discussed below. Id. at 13–16.
i. 	Grommet Spacing
Petitioner asserts that the grommets of the VESA mount adapter
bracket of the ’093 patent “are shown to be VESA standardly-spaced (via
the manufacturer’s blue notations in the below figure) to fit for mounting at
the back of a video monitor.” Id. at 13.
The picture reproduced above shows that one set of four grommets is
positioned 75 mm x 75 mm apart, whereas the other set of four grommets is
positioned 100 mm x 100 mm apart. Ex. 1003, 3.

PGR2019-00030
Patent D823,093 S
12
Petitioner explains that Section 5.2.1 of the VESA FDMI Standard
describes the same two patterns for the “Screw Mounting Interface
Dimensions” on the back of a monitor: (1) 100 mm x 100 mm, for displays
weighing up to 14 kg; and (2) 75 mm x 75 mm, for smaller displays,
weighing less than 8 kg. Pet. 13–14 (quoting Ex. 1002, 28).
ii. 	Grommet Size
Petitioner asserts that the size of the grommets of the VESA mount
adapter bracket of the ’093 patent are also “dictated by VESA Standards.”
Id. at 15. Petitioner points to the following chart from Section 5.6 of the
VESA FDMI Standard, which indicates a 5 mm hole size in the plate3:
Ex. 1002, 32. Thus, Petitioner contends that the grommets “must be
standardly-sized – else they won’t confirm to VESA standards.” Pet. 16.
iii. 	Grommet Raised Edges
Petitioner asserts that “[h]aving raised edges for grommets is known
to increase the strength of the sheet to which the grommets are attached.”
Id. Petitioner quotes a paper from the 17th International Conference on
3 Petitioner refers to this structure as a “plate” (see Pet. 9), whereas the
VESA FDMI Standard refers to it as a “pad” (see Ex. 1002, 32). For
consistency with the Petition, we refer to the structure as a “plate.”

PGR2019-00030
Patent D823,093 S
13
Metal Forming that states: “For the purposes of improving fatigue strength
of the steel sheet, the edge of the hole was thicken[ed]. Thus[,] the fatigue
strength was improved as compared to the normal piercing hole without
thickening.” Id. (quoting Ex. 1006, 5). Accordingly, Petitioner contends
“the grommets [of the ’093 patent] have raised edges as reinforcement so the
sheet to which the grommets are attached will not break under heavy
monitor weight.” Id. at 17.
2. 	Availability of Alternative Designs
Petitioner contends that, in addition to the design being dictated by the
functionality discussed above, alternative VESA mount adapter brackets “all
have the same design or appearance as the black-lined portions of the figures
of the ’093 Patent.” Id. at 20 (emphasis omitted). Petitioner asserts:
This is because the black-lined portions of the figures of the
’093 Patent are necessary for the bracket to function. The black-
lined portions of the figures of the ’093 Patent are not anything
but the functional requirements that are common to similarly
marketed brackets for the same function – this is because to
function, the bracket of [the] claimed design of the ’093 Patent
must have tabs and grommets that meet VESA standards and are
sized and positioned for a specific line of flat panel displays.
Id.
Petitioner provides two examples of other VESA mount adapter
brackets. First, Petitioner points to an “HP Pavilion Monitor VESA
Adapter,” from Gladiator Joe, that Petitioner asserts is “identical, but for
raised grommet edges, to the bracket protected by the ’093 Patent.” Id.; see
Ex. 1007, 1. The Petition includes side-by-side images of Gladiator Joe’s
product and Figure 1 of the ’093 patent, which are reproduced below.
Pet. 21.

PGR2019-00030
Patent D823,093 S
14
Gladiator Joe’s product (on the left) is shown next to Figure 1 of the
’093 patent (on the right). Id.
Second, Petitioner points to a VESA Adapter for certain HP monitors
made by VIVO. Id. at 21–23 (citing Exs. 1008 and 1009). Petitioner asserts
that the VIVO product has the same tabs and grommets as those shown in
the ’093 patent. Id. at 21. The Petition includes side-by-side images of
VIVO’s product and Figure 1 of the ’093 patent, which are reproduced
below. Id. at 22; see Ex. 1008.
VIVO’s product (on the left) is shown next to Figure 1 of the ’093 patent (on
the right). Petitioner further points to VIVO’s identification of the “exact
spacing/ positioning of grommets as the bracket of the ’093 Patent,” which

PGR2019-00030
Patent D823,093 S
15
“match[] the VESA standard measurements,” as shown below. Pet. 22
(citing Ex. 1009, 1).
VIVO’s product is shown above in two images: the first (on the left) shows a
side view and indicates the vertical dimension of the bracket and length of
the bottom tabs, the second (on the right) shows a front/back view and
indicates the width of the bracket and the spacing between the grommets,
which are shown as 75 mm x 75 mm and 100 mm x 100 mm. See id. (citing
Ex. 1009, 1).
Additionally, Petitioner contends that Patent Owner’s webpage
offering for sale an alleged commercial embodiment of the design claimed in
the ’093 patent similarly indicates that the product comports with “Standard
VESA Hole Patterns: 75 mm x 75 mm, 100 mm x 100 mm.” Id. at 24–25
(citing Ex. 1010, 1 (emphasis omitted)). Petitioner asserts the product
description of the alleged commercial embodiment further indicates that it

PGR2019-00030
Patent D823,093 S
16
fits the same HP monitors as the VIVO product. Compare Ex. 1008, with
Pet. 25.4
Petitioner contends that the overall appearance of the patented bracket
is the same as the other bracket products because the overall appearance is
dictated by the functional requirements of the VESA FDMI Standard.
Pet. 25–26. Petitioner asserts:
The 	grommets 	of 	the 	’093 Patent 	are 	required 	by 	VESA
standards . . . ; and the tabs of the ’093 Patent are required to be
angled at roughly ninety degrees to fit onto (in the case of the top
tab) and into (in the case of the bottom tabs) the back of the flat
panel which the bracket of the ’093 Patent supports.
Id. Petitioner further contends that “the bottom tabs are required to be
shaped in such a way in order to interlock with the slots in the back of the
flat panel into which the bracket of the ’093 Patent supports.” Id. at 26.
And, Petitioner again explains that raised edges for grommets was “known
to increase the strength of the sheet to which the grommets are attached.”
Id.
In light of the discussion above, Petitioner contends that “there is no
availability of alternative designs because [the] claimed design of the
’093 [patent] is dictated by VESA standards and needing to fit on and into
monitors made by Hewlett Packard.” Id. Additionally, Petitioner asserts
that the overall appearance of the article, i.e., the claimed design viewed in
its entirety, is similarly dictated by function because “there does not appear
4 Petitioner omits the HP Pavilion 24 cw monitor from its list of monitors
compatable with VIVO’s product. See Pet. 21. VIVO’s product description
on ebay.com, however, includes the HP Pavilion 24 cw monitor. See
Ex. 3001, 2. Thus, we agree that the two products have the same
compatabilities.

PGR2019-00030
Patent D823,093 S
17
to be anything that is not dictated [by] VESA standards and the Hewlett
Packard monitors that it is designed to fit.” Id. Accordingly, Petitioner
contends:
In short, if the claimed design of the ’093 Patent did not
have the overall appearance that it does, then the claimed design
of the ’093 Patent would not function. 	The elements of the
claimed design of the ’093 Patent – viewed in isolation as well
as together – must appear as they do so that the bracket of the
’093 Patent can function. 	Without the elements of the claimed
design of the ’093 Patent – viewed in isolation as well as together
– the claimed design of the ’093 Patent would not fit the very
standard monitors that it must fit to function.
Id. at 26–27 (emphasis omitted); see id. at 29 (“The tabs and grommets are
disposed where they are and positioned where they are because of functional
– not ornamental – considerations. Nothing about the overall shape or the
design and placement of individual elements, for instance, can serve an
ornamental purpose because they are dictated by a functional purpose.”).
Thus, Petitioner asserts “the claimed design is primarily functional and
cannot be the subject of a design patent.” Id. at 29.
3. 	Analysis
On the record before us, we find that Petitioner has shown that it is
more likely than not that the challenged claim of the ’093 patent is
unpatentable. First, the claimed portions of the design include the tabs and
the grommets. Petitioner explained in detail how the spacing, size, shape,
and angle of the tabs are dictated by their function to attach to the back of
certain monitors. Petitioner further explained how the spacing, size, and
shape of the grommets are similarly dictated by their function and the VESA
FDMI Standard. On this record, we agree with and adopt Petitioner’s
reasoning as to these elements as our findings. The only design element that

PGR2019-00030
Patent D823,093 S
18
appears to be optional, i.e., not required to perform the mounting function, is
the raised edges of the grommets. Petitioner, however, sufficiently supports
its argument that it was known that raising the edges of grommets increases
their strength, and, therefore, provides a functional (not ornamental) benefit.
Therefore, on the present record before us, we find that each of the
individual elements of the claimed design appears to be dictated solely by
function.
Second, focusing on the overall appearance of the article, see Berry
Sterling, 122 F.3d at 1456, we are persuaded that, on the present record, the
claimed design for the adapter bracket as a whole appears primarily
functional, rather than primarily ornamental. Of particular significance is
Petitioner’s evidence that other mounting brackets contain the same
individual elements of the claimed design as well as the same overall
appearance of the bracket. Any differences, besides the raised grommets,
between the other bracket designs known in the art and that of the design
claimed in the ’093 patent appear to lie solely in unclaimed features, e.g., the
specific shape of the bracket plate’s perimeter. See, e.g., Pet. 22 (showing
the side-by-side pictures of VIVO’s bracket and Figure 1 of the ’093 patent).
Thus, on this record, there appears to be a lack of alternative designs, which
weighs strongly in Petitioner’s favor.
Accordingly, on this record, we determine that the particular design is
“essential to the use of the article,” L.A. Gear, 988 F.3d at 1123, and, thus,
primarily functional.

PGR2019-00030
Patent D823,093 S
19
IV. 	CONCLUSION
For the foregoing reasons, Petitioner has shown that it is more likely
than not that the challenged claim of the ’093 patent is unpatentable for
lacking ornamentality. 35 U.S.C. § 324(a). At this stage of the proceeding,
however, we have not made a final determination as to the unpatentability of
the challenged claim or any underlying factual or legal issue.
V. 	ORDER
Accordingly, it is:
ORDERED that, pursuant to 35 U.S.C. § 324(a), a post-grant review
of the claim of the ’093 patent according to the ground raised in the Petition
is hereby instituted; and
FURTHER ORDERED that, pursuant to 35 U.S.C. § 324(d) and
37 C.F.R. § 42.4, a post-grant review of the ’093 patent will commence on
the entry date of this Decision, and notice is hereby given of the institution
of a trial.

PGR2019-00030
Patent D823,093 S
20
For PETITIONER:
Michael L. Greenberg
GREENBERG & LIEBERMAN, LLC
michael@aplegal.com
For PATENT OWNER:
James M. Heintz
Dale S. Lazar
DLA PIPER LLP
jim.heintz@dlapiper.com
dale.lazar@dlapiper.com